If your SafeSpec inspection report sent you here, the inspector found sloping floors: floors that are noticeably out of level, sagging between supports, or showing signs of settlement. Some slope is normal in older homes. Some is a sign of a structural problem that is getting worse.
This page explains the common causes, how we measure, what is typical versus significant, and who to call.
Common Causes of Sloping and Sagging Floors
Foundation settlement
Soil under a footing can compress, wash out or shrink and swell with moisture. When part of the foundation drops, the floor framing above it drops too. Settlement often shows up along one side of the house, with matching cracks in foundation walls, brick or drywall.
Undersized or overspanned joists
Floor joists are sized for the distance they span and the load they carry. Joists that are too small, spaced too far apart or spanning too far between supports will sag in the middle over time.
This is common in older homes, additions and areas where someone removed a support to open up a basement.
Failed, missing or poorly built posts and piers
Basement and crawl space posts hold up the main beam. Rusted steel columns, rotted wood posts, stacked blocks, temporary jack posts left in place and posts with no proper footing can all sink or shift and let the floor above drop.
Moisture and wood rot
Wet crawl spaces, plumbing leaks and poor drainage can rot sill plates, joist ends and subfloor. Rotted wood crushes and loses strength. Wood destroying insects can cause similar damage; a termite inspection checks for them. If you are concerned about moisture in a basement or crawl space, SafeSpec also offers mold testing in St. Louis.
Notched, cut or drilled framing
Plumbers, electricians and HVAC installers sometimes cut joists to route pipes and ducts. The building code limits these cuts.
Under the International Residential Code (IRC), notches in solid lumber joists cannot exceed one sixth of the joist depth and are not allowed in the middle third of the span. Holes cannot exceed one third of the joist depth and must stay at least 2 inches from the top and bottom edges. Cuts beyond these limits weaken the joist and can cause sagging.
Removed or altered bearing walls
Interior walls often carry floor or roof loads to the beam below. When a bearing wall is removed for a remodel without a properly sized beam and posts in its place, the floor above can sag and doors can start to bind.
How Inspectors Measure Floor Slope
During a St. Louis home inspection, we use a laser level and a digital level to compare floor heights across rooms and to measure slope over a set distance. We record slope either in inches over a span (for example, 1 inch over 10 feet) or in degrees. For reference:
- 1/4 inch over 32 inches is about 0.45 degrees.
- 1 inch over 10 feet is about 0.48 degrees.
- A 1 percent slope is 1.2 inches over 10 feet, about 0.57 degrees.
- 1 degree is about 2.1 inches over 10 feet.
We also look for related signs: cracks in foundation walls, sticking doors and windows, gaps at baseboards and trim, cracked tile, drywall cracks running from door corners, and sagging or damaged framing seen from the basement or crawl space.
Sloping Floors: What Is Typical vs Significant
There is no single number that makes a floor “bad.” Industry guidance helps frame it:
- New work tolerance. NAHB remodeling standards call for floors to be level within 1/4 inch in 32 inches. Older homes routinely exceed this and are not automatically unsafe.
- Noticeable slope. The Texas Section of the American Society of Civil Engineers guideline for evaluating residential foundations notes that a floor slope greater than 1 percent is usually noticeable. It also says a floor measurement alone should not be the only basis for judging a foundation; symptoms of distress must be considered too.
When to worry about sloping floors
In practice, slope tends to be typical when it is gradual, spread across the house, consistent with the home’s age, and not paired with active cracking or damaged framing.
It is significant when it is concentrated in one area, sharp or dipping, getting worse over time, or paired with:
- Cracks in foundation walls that are wide, offset, or wider at one end
- Doors that will not latch, or that have been trimmed to close
- Cracked, split, rotted or heavily notched joists or beams
- Leaning, sinking, rusted or makeshift posts
- Signs of recent shimming, patching or new trim covering gaps
- Water or moisture problems in the basement or crawl space
A home inspection is a visual inspection. We cannot see framing hidden by finished ceilings and cannot tell from one visit whether movement is ongoing or historic. That is why significant findings are referred to a specialist.
When to Call a Foundation Contractor or Structural Engineer
- Structural engineer first when the cause is unclear, when there are multiple warning signs, when a bearing wall was removed, or when you want an independent opinion before paying for repairs. An engineer evaluates the cause and specifies the fix, and is not selling the repair.
- Foundation contractor to price and perform repairs such as new posts and footings, sistering or adding joists, adding beams, or stabilizing settled foundation sections. Ask whether the work requires a permit and an engineer’s design.
- Before closing if you are buying. Get the evaluation done within your inspection period so you can negotiate repairs or price with real numbers.
- Fix moisture at the same time. If water or rot caused the problem, correct the drainage, leaks or crawl space moisture or the repair will not last.
Frequently Asked Questions
Is it normal for an older house to have sloping floors?
Some slope is normal in older homes. NAHB remodeling standards call for new floors to be level within 1/4 inch in 32 inches, and older homes routinely exceed this without being automatically unsafe. Slope is usually typical when it is gradual, spread across the house and not paired with active cracking or damaged framing.
How much floor slope is too much?
There is no single number that makes a floor bad. The Texas Section of the American Society of Civil Engineers notes that a floor slope greater than 1 percent, or 1.2 inches over 10 feet, is usually noticeable. It also says a floor measurement alone should not be the only basis for judging a foundation; symptoms of distress must be considered too.
When should I worry about sloping floors?
Slope is significant when it is concentrated in one area, sharp or dipping, or getting worse over time. Warning signs include wide or offset foundation cracks, doors that will not latch, damaged joists or beams, and leaning or sinking posts. Moisture problems in the basement or crawl space are another red flag.
What causes sagging floors?
Common causes include foundation settlement, undersized or overspanned joists, and failed or poorly built posts and piers. Moisture and wood rot, joists cut beyond code limits, and bearing walls removed without a properly sized beam can also cause sagging.
Should I call a structural engineer or a foundation contractor for sloping floors?
Call a structural engineer first when the cause is unclear, there are multiple warning signs, or a bearing wall was removed. An engineer evaluates the cause and specifies the fix, and is not selling the repair. A foundation contractor prices and performs the repairs.
Buying a home or have questions about floor slope in your report? Schedule your inspection with SafeSpec, call SafeSpec Home Inspections at (314) 375-6014 or email Inspector@SafeSpec.net. We serve St. Louis City and County, St. Charles County and Jefferson County.
Sources
- Texas Section ASCE, Guidelines for the Evaluation and Repair of Residential Foundations, Version 2
- Journal of Light Construction, “Q&A: Foundation and Framing Tolerances” (NAHB remodeling tolerance)
- International Code Council, 2021 International Residential Code, Chapter 5 Floors
- Winnebago County, IL, “Cutting, Notching and Drilling” (IRC R502.8 summary)